mixer: committing narrow-channel version

but basically I abandon this design

1 files changed, 49 insertions, 28 deletions

diff --git a/mixer.scad b/mixer.scad
index 3740ae5..c298482 100644
--- a/mixer.scad
+++ b/mixer.scad
@@ -26,2 +26,3 @@ module the_mixer(
  join_angle = 30,
+ joint = "wide", // wide|narrow
 
@@ -29,3 +30,3 @@ module the_mixer(
  pushfit_s = 2, // shell around pushfit holes
- output_l = 4, // length of output after before pushfit
+ output_l = 4, // length of output liner after before pushfit
  outer_r = 3, // outer radius
@@ -33,11 +34,42 @@ module the_mixer(
  liner_d_tolerance = .2,
+ filament_d_tolerance = .25
 ) {
  fnd = PI*2*2; fnr = fnd*2;
- module liner(l,in) {
-  inh=ld-liner_id;
-  union() {
-   translate([0,0,inh])
-   cylinder(d=ld,h=l-inh,$fn=ld*fnd);
-   translate([0,0,-epsilon])
-   cylinder(d1=ld+epsilon,d2=liner_id-epsilon,h=inh+2*epsilon,$fn=ld*fnd);
+
+ ld = liner_d+liner_d_tolerance;
+ fd = filament_d+filament_d_tolerance;
+ linero = ld/2/tan(join_angle/2); // liner offset
+
+ jd = (joint=="narrow") ? fd : ld; // joint diameter
+ jo = (joint=="narrow") ? jd/2/tan(join_angle/2) : linero; // joint offset
+
+ pfrx = interpushfit/2/cos(join_angle/2); // radial margin
+ pfR = pushfit_d/2+pfrx;      // radius of pushfit with margin
+ // offset of pushfit offset
+ pfoo = (pushfit_type=="threaded") ? 0 :
+        (pushfit_type=="embedded") ? (pushfit_h-pushfit_ring_h) :
+        (pushfit_type=="embeddest") ? 0 : undef;
+ pfo = pfR/tan(join_angle/2)-pfoo; // pushfit thread ofset
+
+ h = pushfit_d+pushfit_s*2;
+ 
+ module liner(l,in,offset=0,linero) {
+  lo = linero==undef ? l/2 : linero;
+  translate([0,0,offset])
+  if(joint=="narrow") {
+   $fn = max(fd,ld,jd)*fnd;
+   cylinder(d=fd,h=l);
+   //if(in=="top") cylinder(d1=jd,d2=fd,h=(jd-fd)/2);
+   translate([0,0,lo])
+   cylinder(d=ld,h=l-lo);
+   if(in=="bottom") translate([0,0,lo+epsilon]) mirror([0,0,1])
+    cylinder(d1=(liner_id+ld)/2,d2=fd,h=(liner_id+ld-fd)/2);
+  }else{
+   inh=ld-liner_id;
+   union() {
+    translate([0,0,inh])
+    cylinder(d=ld,h=l-inh,$fn=ld*fnd);
+    translate([0,0,-epsilon])
+    cylinder(d1=ld+epsilon,d2=liner_id-epsilon,h=inh+2*epsilon,$fn=ld*fnd);
+   }
   }
@@ -54,3 +86,3 @@ module the_mixer(
    cylinder(d=pushfit_d,h=pushfit_legspace_h,$fn=pushfit_d*fnd);
-   dd = pushfit_d-pushfit_id;
+   dd = (pushfit_d-pushfit_id)/2;
    translate([0,0,pushfit_legspace_h-epsilon])
@@ -62,13 +94,2 @@ module the_mixer(
  
- ld = liner_d+liner_d_tolerance;
- linero = ld/2/tan(join_angle/2); // liner offset
- pfrx = interpushfit/2/cos(join_angle/2); // radial margin
- pfR = pushfit_d/2+pfrx;      // radius of pushfit with margin
- // offset of pushfit offset
- pfoo = (pushfit_type=="threaded") ? 0 :
-        (pushfit_type=="embedded") ? (pushfit_h-pushfit_ring_h) :
-        (pushfit_type=="embeddest") ? 0 : undef;
- pfo = pfR/tan(join_angle/2)-pfoo; // pushfit thread ofset
-
- h = pushfit_d+pushfit_s*2;
  difference() {
@@ -85,5 +106,4 @@ module the_mixer(
   for(s=[-1,1]) rotate([0,0,s*join_angle/2]) {
-   translate([0,linero,0]) rotate([-90,0,0])
-   liner(l=pfo-linero+epsilon,in="bottom");
-   //cylinder(d=ld,h=pfo-linero+1,$fn=ld*fnd);
+   rotate([-90,0,0])
+   liner(l=pfo-jo+epsilon,in="bottom",offset=jo);
    translate([0,pfo,0]) rotate([-90,0,0])
@@ -92,3 +112,3 @@ module the_mixer(
   rotate([90,0,0]) {
-   liner(l=output_l+epsilon,in="top");
+   liner(l=output_l+epsilon,in="top",linero=0);
    //cylinder(d=ld,h=output_l+1,$fn=ld*fnd);
@@ -100,7 +120,7 @@ module the_mixer(
     rotate([-90,0,0])
-    translate([0,0,linero])
-    cylinder(d=ld,h=epsilon,$fn=ld*fnd);
+    translate([0,0,jo])
+    cylinder(d=jd,h=epsilon,$fn=jd*fnd);
    }
    rotate([90,0,0])
-   cylinder(d=ld,h=epsilon,$fn=ld*fnd);
+   cylinder(d=jd,h=epsilon,$fn=jd*fnd);
   }
@@ -114,3 +134,4 @@ module this() {
   pushfit_h = 7,
-  interpushfit = extrusion_width
+  interpushfit = extrusion_width,
+  joint = "narrow"
  );