Try to gracefully shut down the card after sniffing... this is a temporary

hack until the colleagues implement this in libwellenreiter...

2 files changed, 41 insertions, 12 deletions

diff --git a/noncore/net/wellenreiter/README b/noncore/net/wellenreiter/README
index c04d30c..af2e611 100644
--- a/noncore/net/wellenreiter/README
+++ b/noncore/net/wellenreiter/README
@@ -2,11 +2,11 @@
 /*                W e l l e n r e i t e r   I I                          */
 /*               ===============================                         */
 /*                                                                       */
-/*                                                  Version: Opie-ALPHA  */
+ /*                                          Version: Opie-ALPHA-January */
 /*************************************************************************/
 
 --------------------------------------------------
-Release Notes for Opie-ALPHA Version December 2002
+Release Notes for Opie-ALPHA Version January 2002
 --------------------------------------------------
 
 =====================
@@ -15,9 +15,6 @@ Release Notes for Opie-ALPHA Version December 2002
 
 * low-level orinoco_cs-based (including prism2 and spectrum_cs)
 
-* Supported Interfaces: wlan0 (yes, I know this is hardcoded and
-  lame, but we're in a hurry and this can be configured soon...)
-
 =====================
 =      Build        =
 =====================
@@ -32,24 +29,40 @@ noncore/net/wellenreiter/gui
 
 ./configure and rebuild. Note that you need libpcap in your toolchain.
 
+To compile Wellenreiter within the OZ build environment, add the
+following lines to $OPIEDIR/packages
+CONFIG_WELLENREITER noncore/net/wellenreiter/libwellenreiter libwellenreiter.pro
+CONFIG_WELLENREITER noncore/net/wellenreiter/daemon daemon.pro
+CONFIG_WELLENREITER noncore/net/wellenreiter/gui gui.pro
+CONFIG_WELLENREITER noncore/net/wellenreiter/contrib/orinoco_hopper orinoco_hopper.pro
+
+make -f Makefile.test clean-configs
+cd <BUILDROOT>
+make SUBDIRS=packages/opie package
+
 =====================
 =     Install       =
 =====================
 
 Alternatively, you can use our precompiled ipk. Get it from
-http://opie.net.wox.org/elan/current. You will also need libpcap.
+http://opie.net.wox.org/wellenreiter/current/. This also includes a recent libpcap.
 
 =====================
 =       Run         =
 =====================
 
+There are two possible modes: <Manual> and <Automatic>. I suggest, you
+start with the <Automatic> Mode. This works just using the "Start"
+and "Stop" Pushbuttons in the Wellenreiter GUI. If this doesn't work,
+then use the following strategy:
+
 1. Place card in monitor mode. This is device dependent.
 
    Caution: Don't do this while you're logged in via ssh
    or otherwise using the wireless interface - your connection
    will freeze: The card can't be used normally when sniffing!
 
-   For most orinoco-based cards this can be done using
+   For most orinoco-based cards this can be done using either
    'iwpriv <interface> 2' or 'iwpriv <interface> 2 1'.  
    
    You can check if this works, by calling 'ifconfig <interface>'.
diff --git a/noncore/net/wellenreiter/gui/wellenreiter.cpp b/noncore/net/wellenreiter/gui/wellenreiter.cpp
index b22c5cc..4ee9a35 100644
--- a/noncore/net/wellenreiter/gui/wellenreiter.cpp
+++ b/noncore/net/wellenreiter/gui/wellenreiter.cpp
@@ -112,7 +112,7 @@ Wellenreiter::Wellenreiter( QWidget* parent, const char* name, WFlags fl )
     // setup GUI
         
     connect( button, SIGNAL( clicked() ), this, SLOT( buttonClicked() ) );
-    button->setEnabled( false );
+    // button->setEnabled( false );
     netview->setColumnWidthMode( 1, QListView::Manual );
     
     if ( manufacturerdb )
@@ -235,11 +235,28 @@ void Wellenreiter::buttonClicked()
         system( "killall orinoco_hopper" );
         system( "killall wellenreiterd" );
         
-        // FIXME: reset the card trying to get into a usable state again
+        // get configuration from config window
         
-        // for now, just message the user
+        const QString& interface = configwindow->interfaceName->currentText();
+        const QString& cardtype = configwindow->deviceType->currentText();
+        const QString& interval = configwindow->hopInterval->cleanText();
+        
+        // reset the card trying to get into a usable state again
+        
+        QString cmdline;
+        cmdline.sprintf( "iwpriv %s monitor 1", (const char*) interface );
+        system( cmdline );
+        cmdline.sprintf( "iwpriv %s monitor 1 6", (const char*) interface );
+        system( cmdline );
+        cmdline.sprintf( "ifconfig %s -promisc", (const char*) interface );
+        system( cmdline );
+        cmdline.sprintf( "killall -14 dhcpcd" );
+        system( cmdline );
+        cmdline.sprintf( "killall -10 udhcpc" );
+        
+        // message the user
 
-        QMessageBox::information( this, "Wellenreiter/Opie", "You should reset your\ndevice before using it again." );
+        QMessageBox::information( this, "Wellenreiter/Opie", "Your wireless card\nshould now be usable again." );
     }
     
     else
@@ -265,7 +282,6 @@ void Wellenreiter::buttonClicked()
         /* Global::Execute definitely does not work very well with non-gui stuff! :( */
         
         QString cmdline;
-        
         cmdline.sprintf( "iwpriv %s monitor 2", (const char*) interface );
         system( cmdline );
         cmdline.sprintf( "iwpriv %s monitor 2 1", (const char*) interface );