1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
|
layer_height=0.2; extrusion_width=0.45;
epsilon=0.01;
$fs=0.125;
draft=true;
use <threads.scad>;
module pushfit_thread(h=10) {
thr = 3/8 + .5/25.4;
slit = 25.4*thr/2 + 0.2;
if(draft) cylinder(d=thr*25.4,h=h);
else english_thread(diameter=thr,threads_per_inch=28,length=h/25.4,internal=true);
translate([-2,-slit,0]) cube([4,2*slit,h]);
}
module the_mixer(
pushfit_d = 10, pushfit_h = 10,
pushfit_id = 6.5,
pushfit_type = "threaded", // threaded|embedded|embeddest
pushfit_ring_h = 4.7, // height of embedded pushfit ring
pushfit_insert_d = 8, // diameter of pushfit insert legs hole
pushfit_legspace_h = 3.2, // the height of legspace for embeddest variant
pushfit_inlet_ch = 1,
liner_d = 4, liner_id = 2,
filament_d = 1.75,
join_angle = 30,
interpushfit = 2*extrusion_width, // space between two pushfit holes
pushfit_s = 2, // shell around pushfit holes
output_l = 4, // length of output after before pushfit
outer_r = 3, // outer radius
liner_d_tolerance = .2,
) {
fnd = PI*2*2; fnr = fnd*2;
module liner(l,in) {
inh=ld-liner_id;
union() {
translate([0,0,inh])
cylinder(d=ld,h=l-inh,$fn=ld*fnd);
translate([0,0,-epsilon])
cylinder(d1=ld+epsilon,d2=liner_id-epsilon,h=inh+2*epsilon,$fn=ld*fnd);
}
}
module pushfit() {
if(pushfit_type=="threaded") {
pushfit_thread(h=pushfit_h);
}else if(pushfit_type=="embedded") {
translate([0,0,pushfit_h-pushfit_ring_h])
cylinder(d=pushfit_d,h=pushfit_ring_h,$fn=fnd);
cylinder(d=pushfit_insert_d,h=pushfit_h,$fn=pushfit_insert_d*fnd);
}else if(pushfit_type=="embeddest") {
cylinder(d=pushfit_id,h=pushfit_h+1,$fn=pushfit_insert_d*fnd);
cylinder(d=pushfit_d,h=pushfit_legspace_h,$fn=pushfit_d*fnd);
dd = pushfit_d-pushfit_id;
translate([0,0,pushfit_legspace_h-epsilon])
cylinder(d1=pushfit_d,d2=pushfit_id-2*epsilon,h=dd+epsilon,$fn=pushfit_d*fnd);
translate([0,0,pushfit_h-pushfit_inlet_ch-epsilon])
cylinder(d1=pushfit_id-2*epsilon,d2=pushfit_id+2*pushfit_inlet_ch+2,h=pushfit_inlet_ch+epsilon+1,$fn=(pushfit_id+2*pushfit_inlet_ch+2)*fnd);
}
}
ld = liner_d+liner_d_tolerance;
linero = ld/2/tan(join_angle/2); // liner offset
pfrx = interpushfit/2/cos(join_angle/2); // radial margin
pfR = pushfit_d/2+pfrx; // radius of pushfit with margin
// offset of pushfit offset
pfoo = (pushfit_type=="threaded") ? 0 :
(pushfit_type=="embedded") ? (pushfit_h-pushfit_ring_h) :
(pushfit_type=="embeddest") ? 0 : undef;
pfo = pfR/tan(join_angle/2)-pfoo; // pushfit thread ofset
h = pushfit_d+pushfit_s*2;
difference() {
hull() {
for(s=[-1,1]) {
rotate([0,0,s*join_angle/2])
for(ss=[-1,1])
translate([ss*pushfit_d/2,pfo+pushfit_h-outer_r-epsilon])
cylinder(r=outer_r,h=h,center=true,$fn=outer_r*fnr);
translate([s*pushfit_d/2,-output_l-pushfit_h+outer_r+epsilon,0])
cylinder(r=outer_r,h=h,center=true,$fn=outer_r*fnr);
}
}
for(s=[-1,1]) rotate([0,0,s*join_angle/2]) {
translate([0,linero,0]) rotate([-90,0,0])
liner(l=pfo-linero+epsilon,in="bottom");
//cylinder(d=ld,h=pfo-linero+1,$fn=ld*fnd);
translate([0,pfo,0]) rotate([-90,0,0])
pushfit();
}
rotate([90,0,0]) {
liner(l=output_l+epsilon,in="top");
//cylinder(d=ld,h=output_l+1,$fn=ld*fnd);
translate([0,0,output_l])
pushfit();
}
hull() {
for(s=[-1,1]) rotate([0,0,s*join_angle/2]) {
rotate([-90,0,0])
translate([0,0,linero])
cylinder(d=ld,h=epsilon,$fn=ld*fnd);
}
rotate([90,0,0])
cylinder(d=ld,h=epsilon,$fn=ld*fnd);
}
}
}
module this() {
the_mixer(
pushfit_type="embeddest",
pushfit_d = 8,
pushfit_h = 7,
interpushfit = extrusion_width
);
}
if(!false) {
difference() {
this();
cylinder(d=100,h=100);
}
}else
this();
|
